JNP-100G-AOCBO-7M
100G to 4x25G AOC AOC transceiver, 850 nm, multimode, fixed (cable)
- Genuine Juniper
- New, factory sealed
- Pay by card, PayPal or T/T
T/T bank transfer
- Tax invoiceIssued by Rabash Technologies Pte. Ltd., Singapore
JNP-100G-AOCBO-7M at a glance
- 100G to 4x25G AOC 7 m active optical cable
- Digital optical monitoring (DOM) for light levels and temperature
- Commercial temperature rating (typically 0 to 70 °C)
- Genuine Juniper part, new, factory sealed
- Listed for 8 Juniper platform families (see Compatibility)
Specifications
| Part number | JNP-100G-AOCBO-7M |
|---|---|
| Brand | Juniper |
| Standard | 100G to 4x25G AOC |
| Form factor | AOC |
| Data rate | 100 Gb/s |
| Wavelength | 850 nm |
| Media | Multimode fibre (MMF) |
| Reach | 7 m cable |
| Connector | fixed (cable) |
| Digital optical monitoring | Supported |
| Temperature range | Commercial (COM) |
| Condition | New, factory sealed |
Compatibility
- Juniper QFX5120
- Juniper EX4400
- Juniper ACX7100
- Juniper PTX10002
- Juniper MX10004
- Juniper QFX5130
- Juniper MX10008
- Juniper QFX5130E
Description
JNP-100G-AOCBO-7M is a 7 m active optical breakout cable that fans one QSFP28 end out to four SFP28 ends for 4x25G. Stocked as a genuine, new, sealed Juniper item. Diagnostics listed cover transmit and receive power, bias current, case temperature and supply voltage. Confirm the host platform and software release against Juniper's compatibility listing first; the same cable is not accepted by every port on every chassis. Listed maximum power is QSFP28 end: 3.5 W; SFP28 end: 1 W. Juniper lists an operating temperature of 0° C to 70° C. Each SFP28 leg is an independent 25G link once breakout mode is set on the QSFP28 port. Its Juniper part number in the compatibility data is 740-073144. With only 7 m of cable, this one is meant for short, tidy connections close to the switch. Juniper's data gives a maximum power draw of QSFP28 end: 3.5 W; SFP28 end: 1 W. Typical use is distributing 25G to servers from a 100G leaf port over fibre.
Typical uses
- Splitting one high-speed port into four lower-speed links
- Connecting a spine or aggregation port to four servers or switches
- Increasing port density on leaf switches
Before you order
- Confirm your switch or router model and software release support the JNP-100G-AOCBO-7M
- Enable port breakout (channelisation) on the host before connecting
- Measure the run: choose the shortest length that reaches without strain
- Prices exclude import duties and taxes in your country (DAP)
FAQ
How long is the JNP-100G-AOCBO-7M?
The JNP-100G-AOCBO-7M is a 7 m active optical cable with the plugs permanently attached.
Is the JNP-100G-AOCBO-7M genuine and what condition is it?
It is a genuine Juniper part, new, factory sealed, sold by an independent reseller and invoiced by Rabash Technologies Pte. Ltd., Singapore.
Which platforms support the JNP-100G-AOCBO-7M?
Juniper lists it for platform families including Juniper QFX5120, Juniper EX4400, Juniper ACX7100, Juniper PTX10002. Check the full list above and your software release before ordering.
Shipping and returns
Ships from Singapore. Delivery options are confirmed for your destination.
Shipping detailsSee the returns and warranty policy for applicable terms.
Returns and warrantyQuotes are valid for 7 days, payable by card, PayPal or T/T.
Request a quoteRelated part numbers
Product guides & buying advice
technix.guru is an independent reseller and is not affiliated with, sponsored by or endorsed by the brand owners. All trademarks belong to their respective owners.